







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Coral Gables Homeowners Choose Cambria Construction
Coral Gables Construction is an independent Cambria quartz fabricator and installer serving Coral Gables, FL. We cut, install, repair and refinish Cambria surfaces every week, which means we know how the material behaves on a wet saw and at a sink cutout, not just how it looks in a brochure. We are not affiliated with, authorized by or certified by Cambria. We’re a multi-trade residential contractor, so if a Cambria kitchen top comes with new cabinets, an island, a backsplash and a bath vanity to match, one team handles the whole scope. Call (844) 797-9523 for a free estimate.
Key Takeaways
- Independent Cambria quartz installation, repair and refinishing in Coral Gables.
- Not a Cambria dealer and not affiliated with the manufacturer: we’re a fabricator.
- We name the material, the edge profile, the seam placement and the price before a saw touches a slab.
- Seam and edge damage is usually repairable in place; cracks through the body of the stone usually aren’t.
- One contractor covering countertops, cabinetry, backsplash, windows, roofing and more.
Why Trust Coral Gables Construction for Your Cambria Construction?

Quartz isn’t stone in the geological sense. It’s ground quartz bound in resin, and that resin is what fails first. A fabricator who treats Cambria like granite, grinding a dry edge or slapping a hot pot on it, is a fabricator who’ll cost you a slab. Our technicians have up to 12 years of experience with quartz surfaces, and they work to one rule: cut and finish the material the way the manufacturer specifies so the warranty stays intact.
That’s what warranty-safe practice looks like in practice. Support rails under any overhang beyond the slab’s own span. Color-matched quartz epoxy on every seam, not clear silicone. Wet-polishing and a controlled feed rate on the saw so the edge doesn’t chip and the surface doesn’t scorch. Sink and cooktop cutouts with the corners eased, because a sharp inside corner on a quartz cutout is where a crack starts.
We also won’t sell you a new countertop when a repair will do. Because we’re independent, we can tell you plainly when a seam can be routed, re-glued and polished back to factory sheen, and when the crack runs deep enough that the slab has to come out. That honesty is worth more than a dealer badge.
One contractor, every trade. A Cambria installation in Coral Gables usually touches cabinetry, backsplash tile, plumbing fixtures and sometimes electrical for under-cabinet lighting. We cover all of it without a chain of specialty subs.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Cambria Construction Problems We Fix in Coral Gables
Quartz failure modes are predictable once you’ve seen enough of them. Here are the five that bring people to the phone.
- Edge chipping at sink and cooktop cutouts. This is impact or an unsupported overhang, almost never a manufacturing defect. The thin band of material around a cutout has less backing than the rest of the slab, so a heavy pot or a leaned-on elbow can knock a chip loose. Repair means rebuilding the edge with color-matched epoxy, shaping it and polishing it back so the chip disappears into the profile.
- Etching and dull spots from acidic cleaners. Vinegar, lemon juice, some lime-scale removers and certain bathroom sprays attack the polished finish and leave a flat, cloudy patch. The resin is etched, not stained, so wiping won’t fix it. We re-polish the affected area back to the same sheen as the rest of the top.
- Hairline cracking and seam shadowing. Two slabs joined without proper color-matched epoxy and a support rail will work against each other under normal use. A dark or widening line along the joint is the tell. The fix is to route out the old adhesive, back-butter the seam, re-glue and re-polish the joint.
- Heat scorching and resin burn. A hot pan set directly on the surface near the range can leave a permanent yellow-brown mark. Quartz handles daily kitchen heat but not a pan straight off a burner. Light scorch sometimes buffs out; deep resin burn doesn’t, and that section gets replaced.
- Moisture and mold at the backsplash joint. Coral Gables humidity finds every unsealed gap. A caulk line behind a Cambria top that was never properly sealed traps moisture against the drywall and starts a mold problem behind the counter. We cut out the old bead, dry the substrate and re-seal with a flexible kitchen-grade sealant.
Here’s how a typical Cambria call usually goes. A homeowner notices a dull ring around the sink or a hairline shadow along a seam on a Brittanicca or Ella top. The usual cause is a cleaner with acid in it, or a seam that was never back-buttered and supported with a rail, so the two slabs have been working against each other. A qualified fabricator dries and assesses the seam, routes out the old epoxy, re-glues with color-matched quartz adhesive and re-polishes the joint. If the crack crosses the sink cutout, the conversation turns to whether the run can be re-supported or the slab has to be replaced.
Cambria Parts & Our Repair-vs-Replace Approach

There’s no meaningful aftermarket “part” for a slab of quartz. The honest choice is between repairing the existing material and replacing it, and we’d rather tell you which one you’re facing than sell you the bigger job.
Where we can repair in place, we do. Seams and chips get rebuilt with color-matched Cambria-spec quartz epoxy, shaped to the original edge profile and polished back to factory sheen. That’s a same-day job in most cases, and the customer stays in their kitchen. Etching gets re-polished rather than patched. Loose seams get re-supported with a rail underneath before any adhesive goes back in.
Where it doesn’t make sense to repair, we say so. A crack that runs through the body of the stone won’t hold under a new epoxy line, and a failure over a dishwasher cutout sits in a spot that gets heat and moisture cycling every day. Those runs come out and get replaced. No claim of stocking Cambria parts, because there’s no such inventory to stock: slabs are cut per job.
If you’re not sure which side of that line your countertop is on, call us. An assessment costs you nothing and the answer is usually clear within a few minutes.
Our Cambria Service Process – Step by Step
- 1
Diagnosis. We look at the damage, the seam placement, the overhang span, the substrate under the slab and the cutout condition. We ask what cleaners have been used, because acid etching and a resin scorch look similar at a glance and get fixed very differently.
- 2
Template and plan. For a new install, we template the cabinets with a physical jig, not a tape measure and a guess. That’s how the seam lands where you want it, not where the slab forces it. For a repair, we specify the epoxy color and the re-polish schedule before we touch the surface.
- 3
Fabrication or repair. Slabs are wet-cut, edges are profiled and polished, seams are back-buttered and glued, and overhangs get rail support. On a repair, the old adhesive comes out, the joint is re-glued and the area is polished back to match.
- 4
Install and test. Countertop set, seams checked for shadow and level, sink and cooktop openings verified, backsplash joint sealed, plumbing reconnected and tested. We run water, check for leaks at the trap, and confirm the dishwasher clearance.
- 5
Warranty and handover. You get care instructions in writing and a record of what was done. Workmanship is backed by our warranty. Call (844) 797-9523 to book your free estimate.
See the difference
Before
After
Before
After
Before
AfterCambria Products We Service & Install in Coral Gables

Cambria is a quartz surface brand, and quartz surfaces cover a lot of ground. We install and service Cambria for kitchen countertops, including perimeter runs and sink surrounds, and for full kitchen islands where the seam placement matters most. We do bathroom vanities and shower surrounds in Cambria quartz, plus backsplash work where a quartz slab or a quartz-to-tile transition needs a clean finished edge.
We work with the recognizable looks as they come up: Cambria Ella for a marble-look white with soft gray veining, Brittanicca for bold gray on white, Torquay for a warm beige-taupe movement, Blackwood when a dark, dramatic vein is the point. Which one suits a Coral Gables kitchen depends on your cabinet color, your lighting and how much movement you want to live with.
We also repair and refinish existing Cambria tops: re-polishing etched areas, rebuilding chipped edges, resetting shadowed seams and re-sealing backsplash joints. No claim of what’s stocked, because slabs are selected per job.
We Also Service These Brands
We’re not a single-brand shop. Cambria quartz is one option among several, and homeowners benefit from comparing them side by side rather than taking what’s handed over. We also install and service KraftMaid and Wellborn cabinetry, Silestone quartz surfaces, and Kohler and Toto fixtures, plus Grohe fittings where a kitchen or bath spec calls for them. That range means you can compare material, finish and price across brands without changing contractors.
FAQs – Cambria Construction Service in Coral Gables
No. Coral Gables Construction is an independent Cambria fabricator and installer, not a Cambria dealer and not authorized or certified by the manufacturer. We buy Cambria slabs through normal supply channels and install, repair and refinish them to the manufacturer’s standards. That independence is why we can tell you honestly when a repair will do and when a slab has to go. Call (844) 797-9523 for a free estimate.
Yes. For quartz surfaces, the “parts” are the adhesive, the support rail and the polishing consumables. We use color-matched Cambria-spec quartz epoxy, structural support rails under overhangs, and polishing pads and compounds appropriate to a resin-bound quartz surface. We don’t use clear silicone on seams or dry-grind an edge, because both compromise the finish and the warranty. Call (844) 797-9523 to talk through your job.
Seam repairs and edge chip repairs are usually a few hours on site. A full countertop replacement takes longer, because the slab has to be templated, fabricated and then installed, and that’s a multi-day process from template to set. Once installed, the countertop is usable the same day. Call (844) 797-9523 for a timeline on your specific project.
Cambria quartz surfaces: kitchen countertops, islands, bathroom vanities, shower surrounds and backsplash work. We do new installs, repairs, edge and seam restoration, re-polishing and re-sealing. If it’s a Cambria surface in your Coral Gables home, we can assess it. Call (844) 797-9523.
Not if the work is done to the manufacturer’s installation standards. The warranty risk comes from improper fabrication and improper care: unsupported overhangs, dry-cut edges, silicone seams, and acid cleaners. We work to spec so the warranty stays intact, and we’ll show you what the care requirements are in writing. Call (844) 797-9523 for a free assessment.
Typical estimated ranges for Cambria work in Coral Gables are below. The written estimate sets the final price, and it’s free.
| Service | Typical Estimated Range |
|---|---|
| Countertop Installation (Cambria quartz) | $2,000 – $6,500 |
| Kitchen Island Installation | $3,000 – $10,000 |
| Backsplash Installation | $800 – $2,500 |
| Cabinet Installation | $4,000 – $13,000 |
Call (844) 797-9523 for an exact quote. Estimates are free. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Usually, yes. A chip at the sink edge is repaired by rebuilding the missing material with color-matched quartz epoxy, shaping it back to the original edge profile and polishing it flush. The repair is invisible in most cases when the color match is right. The exception is when the chip has left the edge thin enough to fail again, or when the overhang underneath was never properly supported, in which case the support has to be corrected first. Call (844) 797-9523 to have it looked at.
Almost always an acidic cleaner. Vinegar, lemon, some lime-scale removers and certain bathroom sprays etch the polished resin surface and leave a dull ring that looks like a stain but isn’t. Wiping won’t bring the shine back. The fix is re-polishing the affected area back to the sheen of the rest of the top, and switching to a pH-neutral stone cleaner afterward. Call (844) 797-9523 for a re-polish estimate.
A properly made seam should be barely perceptible, not invisible. The joint is there, but with a good color-matched epoxy and proper back-buttering it should read as a faint line from arm’s length and disappear under normal lighting. A dark, wide or shadowed seam means the adhesive was wrong, the seam wasn’t back-buttered, or the support underneath is missing. That’s a repairable seam in most cases. Call (844) 797-9523 for an assessment.
No. Quartz is resin-bound, and a pan straight off the burner runs hot enough to scorch the resin and leave a permanent mark. Trivets and a landing zone beside the range are the habit worth building. Light surface scorch sometimes buffs out; deep resin burn doesn’t and requires replacing that section. Call (844) 797-9523 if you already have a mark and want to know which category it falls into.
Yes. Cambria quartz is a strong fit for bathroom vanities and shower surrounds. It doesn’t need sealing like natural stone, and the non-porous surface holds up against soap, water and the moisture a Coral Gables bathroom sees. It’s also cooler to the touch than many alternatives. The one thing to watch is acidic bathroom cleaners, which etch quartz the same way vinegar etches a kitchen top. Call (844) 797-9523 for a bathroom vanity estimate.
Book Your Cambria Service in Coral Gables, FL
Whether it’s a new Cambria island, a chipped sink edge that needs a proper repair, or a full kitchen with Cambria tops, KraftMaid cabinets and a glass backsplash, Coral Gables Construction handles the whole project under one agreement. Free estimates, written line-item pricing and a written workmanship warranty on every job. Call (844) 797-9523. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Coral Gables Construction.












