







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Coral Gables Homeowners Choose ViewLux Construction
Coral Gables Construction provides independent ViewLux construction service in Coral Gables, FL, and we’re not affiliated with or authorized by ViewLux. What sets our ViewLux work apart is component-level knowledge: we understand how ViewLux cabinetry and surfacing behaves in South Florida humidity, how doors and drawer fronts should be shimmed and sealed, and how those components integrate with stone, tile and impact-rated construction. One contractor, every trade, from the driveway to the roofline.
ViewLux makes cabinetry and surfacing components, not finished rooms. That matters. A room only performs as well as the installation and sequencing behind it, and Coral Gables homes ask more of that sequencing than most. The city is master-planned Mediterranean Revival, largely built between the 1920s and 1970s, and exterior work runs through the Board of Architects and the city’s own building department before anything gets built. Add a May-November hurricane season, heavy summer rain and constant humidity, and a ViewLux kitchen in Coral Gables is never a simple permit-and-build job.
Our technicians have up to 12 years of experience with cabinetry and surfacing installation. Call (844) 797-9523. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Coral Gables Construction for Your ViewLux Construction?

Our technicians know ViewLux products at the component level, and that’s the difference between a kitchen that holds up and one that starts failing in a few seasons. ViewLux V-Series Shaker doors, Contempo flat-panel fronts, quartz tops and vanity cabinetry each have their own install and moisture realities. We work with those realities instead of treating every cabinet the same way.
On parts, we’re specific. We use ViewLux OEM doors, drawer fronts, panels and trim when the goal is matching an existing run, and only aftermarket hinges or drawer slides when OEM is discontinued or lead times make it impossible. In every case we match the existing mounting pattern so hardware lines and reveals stay true. No drilling guesses, no universal slides that bind after a year.
Warranty-safe practice matters here too. We document what we remove, what we replace and why, we reseal cut edges and sink cutouts, and we correct the moisture or ventilation problem behind the failure rather than covering it. That record is what a manufacturer’s warranty review is looking for. We’re an independent ViewLux service provider, not a dealer, and we don’t claim factory certification. What we do claim is working knowledge of how these components are built and how they fail in Coral Gables humidity.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common ViewLux Construction Problems We Fix in Coral Gables
Most ViewLux failures we see in Coral Gables trace back to moisture, heat or support, not to the product itself. These are the patterns worth knowing.
- Thermofoil edge lift on Contempo-style doors and drawer fronts. Vinyl-wrapped fronts blister and peel at the edges when humidity works under the wrap and heat from an adjacent oven or cooktop softens the adhesive. It starts at a corner and spreads along the seam. Once the wrap lifts, moisture gets to the core underneath.
- Seam swelling and delamination on painted or foil-wrapped frames. Where box components meet in laundry rooms, baths and under-sink cabinets, trapped moisture swells the joint and the finish delaminates. These are the rooms where a cabinet sits against a wet wall with little air movement.
- Swollen core panels at cut edges. Particleboard and MDF cores soak up water at sink bases and dishwasher-side panels. When those edges swell, drawers bind and door reveals close up unevenly, and no adjustment fixes a box that has physically grown.
- Cracked quartz and solid-surface tops at cutouts and overhangs. A sink cutout or an unsupported overhang concentrates stress, and a top that wasn’t properly supported or sealed at the cut will crack. High-traffic corners chip for the same reason: no give and no protection.
- Uneven reveals and binding drawers after a top settles. When a quartz top is reinstalled over a box that has moved, or shims compress under load, the fronts go out of alignment. It reads like a door problem and usually isn’t.
A ViewLux Contempo-style kitchen in a Coral Gables home often develops peeling at the door edges and a swollen sink-base panel within a few seasons, with drawers that begin to bind and door reveals that tighten unevenly. The usual cause is moisture wicking into the MDF core at cut edges and near the sink, combined with thermofoil lifting where a door sat close to heat. A qualified local pro typically pulls and inspects the affected fronts, checks the box for swelling and fastener integrity, replaces damaged doors and the sink base with OEM or pattern-matched components, reseals cut edges and sink cutouts, and corrects ventilation or under-sink moisture before reinstalling tops and hardware.
ViewLux Parts & Our Repair-vs-Replace Approach

Parts selection is where a ViewLux repair succeeds or quietly fails. We match OEM doors, drawer fronts, panels and trim to an existing run whenever the goal is continuity, and we’ll tell you honestly when OEM is discontinued or the lead time won’t work. In that case we source aftermarket hinges, slides or pattern-matched panels that fit the existing mounting pattern, so the run stays consistent and nothing gets redrilled to fit a part that was never meant for it.
Repair is the honest call for localized damage: a few delaminated fronts, one chipped top corner, a single door that lifted at the edge. Replacing a whole run or an entire cabinet box is the right call when core panels have swollen, when multiple doors have delaminated, or when the box has lost its fastener integrity. Patching a swollen box is money spent twice.
We’re clear about what we are. We repair, install and service ViewLux equipment with quality parts that fit it. We don’t stock or carry genuine ViewLux parts, and we’re an independent provider rather than a dealer. Call (844) 797-9523 for a free estimate and a straight answer on repair versus replace.
Our ViewLux Service Process – Step by Step
- 1
Diagnosis. We inspect the fronts, boxes, tops and hardware, check for moisture at cut edges and under-sink panels, and separate cosmetic wear from structural swelling. That determines what’s repairable and what isn’t.
- 2
Repair or install. For repairs, we pull affected fronts and the sink base, replace with OEM or pattern-matched components, reseal cut edges and sink cutouts, and correct the moisture or ventilation source. For installs, we shim and level to the existing run, set reveals to a consistent line, and sequence the ViewLux quartz tops after the boxes are true.
- 3
Test. Doors and drawers get cycled through full travel. We check reveal lines, drawer glide and hardware alignment, then confirm tops sit supported and sealed with no rock.
- 4
Warranty and record. We hand over a documented record of what was removed, replaced and resealed, which is what a manufacturer’s warranty review asks for. Workmanship on our installation is backed by our warranty.
See the difference
Before
After
Before
After
Before
AfterViewLux Products We Service & Install in Coral Gables
We service and install ViewLux V-Series Shaker-style kitchen cabinets, Contempo flat-panel and slab-door kitchen cabinets, quartz and solid-surface countertop and backsplash components, and ViewLux vanity and bath cabinetry lines. That covers full kitchen remodeling, cabinet installation and refacing, and quartz or granite countertop work, plus the bathroom cabinetry that shares the same box and front construction. We don’t claim to stock any of it. We coordinate independent local construction professionals who work with these components daily, and we sequence the install so the cabinets, tops and backsplash go in the right order for a South Florida remodel. If you’re weighing a small partial update against a full run, we’ll price both.
We Also Service These Brands
We’re not tied to a single brand, and that matters when you’re comparing materials. Alongside ViewLux, we work with KraftMaid and Wellborn cabinetry, Cambria, Silestone and Caesarstone surfacing, and Kohler, Toto and Grohe fixtures. Specify by name, not by category, and we’ll help you weigh the real differences before anything is ordered. Matching an existing run across brands is often the practical answer.
FAQs – ViewLux Construction Service in Coral Gables

No. We are an independent ViewLux service provider and we are not affiliated with, authorized by or certified by ViewLux. We repair, install and service ViewLux products with quality parts that fit them. If a manufacturer’s authorization matters to your project, ask us directly and we’ll tell you exactly where we stand.
Often, yes. We start with OEM ViewLux doors, drawer fronts, panels and trim when they’re available. When a profile is discontinued or the lead time won’t work, we pattern-match the panel and finish and fit aftermarket hardware to the existing mounting pattern so the run stays consistent. Finish and edgebanding matching is the part that separates a good repair from an obvious one. Call (844) 797-9523 to discuss your specific fronts.
Humidity working under the vinyl wrap, usually combined with heat from a nearby oven or cooktop softening the adhesive. Coral Gables’ subtropical air and the moisture a kitchen generates give the wrap a path to lift at a corner, and once it lifts the core underneath starts absorbing water. Resealing the cut edges and correcting the heat or moisture source is part of the fix, not just replacing the front.
If swelling is confined to the sink base, replacing that box is usually the honest fix. If core panels across the run have swelled and multiple doors have delaminated, replacing the run costs less over time than patching boxes that have lost their fastener integrity. We’ll tell you which one you’re looking at after an inspection. Call (844) 797-9523 for a free estimate.
Tops go in after the boxes are shimmed, leveled and true, with cutouts sealed and overhangs supported. In Coral Gables humidity, an unsealed sink cutout or an unsupported overhang is where a quartz top cracks. We sequence cabinet install, then top templating and setting, then backsplash, so nothing gets set on a box that will still move.
Yes, and often faster. Bathrooms combine high humidity with a wet wall and little airflow, so under-sink panels swell and foil-wrapped frames delaminate sooner than in a kitchen. Ventilation and edge sealing matter more there, not less.
Typical estimated ranges for the work we do around ViewLux components are below. These are estimates only; the written estimate you receive sets the final price, and there are no change orders on a fixed scope.
| Project | Typical estimated range |
|---|---|
| Full Kitchen Remodeling | $14000 – $45000 |
| Small & Partial Kitchen Remodels | $9000 – $20000 |
| Cabinet Installation | $4000 – $13000 |
| Cabinet Installation & Refacing (refacing component) | $4000 – $13000 |
| Quartz & Granite Countertops | $2000 – $6500 |
| Backsplash | $800 – $2500 |
| Kitchen Island Installation | $3000 – $10000 |
Call (844) 797-9523 for an exact quote – estimates are free.
Book Your ViewLux Service in Coral Gables, FL
Whether you’re repairing peeling ViewLux fronts, replacing a swollen sink base, or specifying a full ViewLux kitchen with quartz tops in Coral Gables, one contractor handles the scope from the driveway to the roofline. Free estimates, written line-item quotes, fixed pricing with no change orders. Call (844) 797-9523. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Coral Gables Construction.












